DKU 5 PROLIFIC USB DRIVER DOWNLOAD

To do this cut the cable a couple of inches 5 cm from the phone connector. Most of the cable should remain attached to the USB connector, but you need to leave enough cable attached to the phone connector to be able to strip the wires and attach an alligator clip or a terminal block if you like. Installing PC Suite The installation is pretty straight forward. You can now use the ‘File Manager’ to navigate to your Inbox or gallery or any other folders that show up, depending on your phone model, and copy paste to it. Unfortunately i have no good experience with cheap chinese DKU-5 but i have found CA cable the best for me… It has only three wires.. The 10k and 15k resistors on the Tx pin form a voltage divider to reduce the 5V output to 3.

Uploader: Taurr
Date Added: 3 March 2015
File Size: 41.91 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 34604
Price: Free* [*Free Regsitration Required]

These cables vary a good bit.

DriverMax – Ports – DKU-5 – DKU-5 Computer Driver Updates

It’ll finish installing and you’ll get the success screen. I also had two additional wires, one green pin 3one red pin 4.

Proliifc arduino recognises both the sent values and garbage with LCD display…. Recent versions of Linux have the driver pre-installed. If you hold the button too long Arduino will eventually give up and report that the programmer is unavailable. Any chance you could send the driver to me or post it somewhere?

  A4TECH OPTICAL MOUSE SWOP - 35 DRIVER DOWNLOAD

On successful installation, you’ll get the screen shown below. What ultimately worked for me was to fill the via with solder, tin the wire, then place the wire over the via and the iron directly on the wire.

Attach the black cable to the wire which corresponds pin 8 GND. I would need the exact same thing, but 3. Connect proliric 5 and 8 to your multimeter and see if it shows 5V.

The 10k and 15k resistors on the Tx pin form a voltage divider to prolifix the 5V output to 3. However, mine only has 4 wires, and they connect to instead of 4 The link from the above post for the drivers is here: I used screen as my serial communications program. Do not hook up your USB cable just yet. Other chip versions may not be; Check their datasheets.

Ports – Prolific Technology Inc. – Nokia DKU-50 USB Computer Driver Updates

Pick up a version that’ll suit your phone. You can now use the ‘File Manager’ to navigate to your Inbox or gallery or any other folders that show up, depending on your phone model, and copy paste to it. The 1k resistor on the Rx pin prolifoc for limiting the current through the input protection diode if the Tx line exceeds 5V.

Not all pins will have a connection.

I wish they could do bitbang. Follow the instructions; connect your cable porlific phone and then the cable to the computer; make sure your phone isn’t security locked. Now, considering you did not have a pinout of the cable, you can identify which color cable is what, write those down somewhere and get a 4 pin header for soldering the wires on.

  D-LINK DFM MODEM DRIVER

D, and it can only dk programmed once. My cable appears to have been constructed differently — see pics: A resettable fuse is highly recommended.

DriverMax – Ports – Prolific Technology Inc. – Nokia DKU USB Computer Driver Updates

Just plug in the cable without the phone. Hi, I got here via hackaday too, although the comments say that this has been done before your article has introduced me and doubtlessly others to this technique and I think its a great tutorial. But since the others are kinda in between these two flavours, should work. If that doesn’t work, try the steps below. You should notice a new ttyUSB is added after you connect the cable.

Plug in the cable, power on the device, and start the Arduino IDE. You should double check your work because the wires are very thin and the pins are small and close together.